Disclaimer: The information on this page has not been checked by an independent person.   Use this information at your own risk.
ROYMECHX clone of ROYMECH

Click arrows to page adverts


Home
Seals Index



Rotary Seals

Introduction

These notes include descriptions of the following seal types.

  1. Labyrinth Seals
  2. Felt Seals
  3. Lip Seals
  4. FerroFluid Seals

Mechanical Seals are widely used for rotary shaft seals these are reviewed on another page Mechanical Seals



Labyrinth Seals

A labyrinth is defined as a complicated network of passages.  A labyrinth is provided to prevent the easy passage from the entry to the exit.

The labyrinth seal provides the same function.  The Labyrinth Seal restricts the passage of solid, liquid and gaseous contaminants into the sealed area and also restricts the leakage of fluid out of the sealed containment.

Non-contacting rotary and stationary elements provide a restricted flow path and utilize centrifugal force and gravity to prevent leakage.

Unlike other rotating e.g lip seals, the Labyrinth Seal will not damage shafts and has a virtually unlimited life, is frictionless, is largely unaffected by high or low temperatures and can be used for high shaft rotating speeds.

Sealing depends on the form of the labyrinth gap and the length of the leakage path. Rings on the shaft and grooves in the housing provide the basic labyrinth.   At least three groves should be used to provide adequate sealing; clearances vary between 0.25 to 1.0 mm, depending on the speed and temperature the seal is operating in.

More efficient forms of labyrinth seal use alternating teeth of alternating serrations. Smaller gaps produce less leakage but the gap has to be large enough to avoid contact.

The obvious disadvantage of the labyrinth seal is that there is an engineered gap.   This type of seal does not work well if the shaft is not rotating and is not really effective at sealing across high pressure differentials.




Labyrinth Seal Variations

Felt Seals

Felt seals are mainly used as oil or grease seals for retaining lubrication and at the same time preventing dirt or dust entering the bearing.

Felt has long been used for sealing duties because of numerous favourable properties such as wicking and oil absorption properties, fine filtering and resilience. This allows the felt to maintain a constant sealing pressure and as the seal wears the felt surface remains unchanged.

Felt seals are usually pre-saturated with lubricants of a higher viscosity than the bearings offering positive bearing protection.   If the seal does run dry it will tend to protect and polish the shaft rather than cause damage.    Through normal operating temperatures and conditions the felt seal is highly economical, normally requiring replacement when the machine is overhauled.

When the seal is correctly installed the seal is effective over a variety of operating conditions and a wide range of speeds.   Normal maximum rubbing speed is 10 m/s but can be as high as 20m/s if the rubbing surfaces are highly polished and lubricant is always present.

Felt Seals are not suitable for oils with extremely low viscosity or the lubricant is pressurised.


Felt Seal

Lip Seals

This is an assembly consisting of a rubbing elastomer ring seal element held in place by spring.   The seal friction is reduced as an oil film is generated between the lip of the seal and the shaft.  Any damage to the shaft where the seal runs will cause leakage because the optimum oil film thickness will be exceeded locally.   Therefore the shaft finish is especially important, as leakage will occur if an irregular surface is present.

The lubricated rubbing provides the sealing action.   This sealing action cannot be maintained at high speeds if the shaft is not running perfectly true.   To maintain oil film thickness the seal must follow any shaft movement.    This becomes difficult when the shaft is subject to eccentric running or vibration at high speeds.   Typically these seals will operate in the region of 18 m/s and the seals are affected by friction.




Lip Seal

Ferrofluid Seals

This is a very specialised rotary seal type which has superior theoretical benefits.

The seal is a fluid ring which is retained in place between the rotating and fixed members under the action of magnetic forces.

Ferrofluidic sealing technology takes advantage of the response of a fluid, containing a uniform distribution of magnetic particles, to an applied magnetic field. It uses a magnet with magnetically permeable north and south pole pieces and a magnetically permeable shaft to create a permanent magnetic circuit. The magnetic flux is concentrated in the gap under each pole and when ferrofluid is applied to this gap it assumes the shape of a liquid o-ring and produces a hermetic seal.

Ferrofluidic seals offer provide hermetic sealing, long life, virtually frictionless sealing and smooth operation. They are non-contaminating, highly reliable and can operate at high speeds. This type of seal can be used over a wide temperature range, which can be increased by use of cooling, or heating circuits.

The seals have to be regularly maintained as the fluid properties deteriorate over time.

These bearings are used for very specialised applications.

Ferrofluid Seal


Ferrofluid Seal

Other Types of Rotary Seals

Variations on the themes established above include for brush seals and finger seals.





Links Providing information on Rotary Seals
  1. James Walker ...Well known UK Supplier
  2. Garlock ...A supplier of a wide range of seal products
  3. MSO Seals...Lots of information on rotary seals including profiles
  4. Acorn_Ind... Good site with description of various Rotary Seals
  5. ferrotec... Ferrofluid Seals
  6. SKF-Industrial seal self study guide... Detailed guide to seals for bearings

This Page is being developed

Home
Seals Index Page

Send Comments to Roy Beardmore

Last Updated 25/01/2013